SNpixel V4.0 Instructions – CXSABER Skip to content

SNpixel V4.0 Instructions

SNpixel V4.0 Instructions

// size of product

[Handle material] aluminum alloy 6063 [blade material] concentrated PC

[Lamp belt] RGB glass fiber board lamp belt [horn] 4 O'O 2 watts

[Battery] 18650 battery 3200 mah [sword blade size] 82 / 92cm

[Usage time] about 4 hours [charging time] about 2 hours

[Sound] 27 sets (Luke / Obi-wang / Vida / Anakin / Dharma / Asoka / Karl / Yoda / Keloran / Starkiller / Dark Sword...)

[Conventional light efficiency] 9 kinds

[Ignition effects] 11 kinds

[Packaging information] Handle * 1, blade * 1, charging cable * 1, kit * 1 manual * 1

* Have a Power up prompt sound after correctly installing the battery. * Charging prompt sound when charging correctly

Single push button / / push button operation

Standby state: usually the button light is on but the blade is not on

Power on state: usually refers to the state where the button light is on and the blade light effect is on

Switch blade length 82 / 92: Turn off (button light is not on) quickly click the button three times until you hear the voice prompt

Operation is performed in the standby state

Wake up the lightsaber: long press the button until the button light is on, and then enter the standby state

Open the sword: Click the button

Adjust the volume: Long press the button to release the breathing light after flashing once

Switch the boot effect: long press the button to the breathing light flashes 2 times after release

Switch the conventional light effect: long press the button to the breathing light flashes 3 times after release

Switch sound: Long press the button and release until the breathing light flashes 4 times

Power saving mode: enter the power saving mode without operation within 10 minutes

Operation in the boot state

Blaster Shockwave: Click on the button

Flash lock-up: long press the button until the breathing light flashes 1 time before release

Switch blade color: press the button to release the breathing light 2 times

FOC off / On: Long press the button until the breathing light flashes 3 times before release

Jian: Long press the button until the breathing light flashes 4 times

Single-button / / motion-sensing operation

Operation is performed in the standby state

Open the sword: fast left turn + right turn (or right turn + left turn) handle

Switch sound: blade up, hold the button and quickly turn left + right (or right + left) handle

Switch BGM: blade down, press and hold the button and quickly turn left + right (or right + left) handle

Operation in the boot state

Close, turn left + turn right (or right turn + turn left) handle

Switch blade color: blade down, press and hold the button and quickly turn left + right (or right + left) handle

Force: blade up, hold the button and quickly turn left + right (or right + left) handle

FOC tapping: tap the lightsaber

Drag Drag the floor: hold down the button and hit the blade

Melt fuse: hold the button and stab forward

 

Double button / / button operation

(Upper and lower button setting: upper-main button / lower-secondary button; left and right button setting: left-main button / right-secondary button)

Switch blade length 82 / 92: Shutdown state (power off) Quickly click the main button six times until you hear the voice prompt

Operation is performed in the standby state

Open the sword: Click on the main button

Switch sound effects: Click the secondary button

Adjust volume: press the primary / secondary button to release the prompt tone, then click the main button to increase the volume mode, and click the secondary button to turn down the volume. To exit this mode, hold the main / secondary button and release the prompt

Switch the boot effect: long press the main button for 1 second after hearing the prompt sound release

Switch the conventional light effect: long press the secondary button for 1 second after hearing the prompt sound release

Shutdown (power off): Quick click the secondary button three times

Power saving mode: enter the power saving mode without operation within 10 minutes

Operation in the boot state

Guan Jian: Click on the main button

Blaster Shockwave: Click on the secondary button

Lock-up: press the secondary button for 1 second and release

FOC off / On: Turn FOC on or off after holding the main / secondary button

Dual button / / motion sensing operation

Operation is performed in the standby state